Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected issues. Fortunately, resetting your Holosun is a easy process that can be achieved in just a few steps.

• Begin by ensuring your red dot sight is powered on.
• Identify the small reset button on the rear of the device.
• Use a paperclip to press and hold the reset switch for approximately 5 moments.
• Let go the switch and your Holosun EPS Carry Red Dot sight will power cycle.
• Your red dot sight should now be reverted to its factory settings.

Return to Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to its factory configuration is a breeze. First, determine the tiny button on the rear of your optic. Then, press and hold it for around ten seconds until you see the indicator light change. Your Holosun EPS Carry is now reset to its factory settings, ready for consistent targeting.

revive your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Hold down the power button for approximately 7 seconds.
• The display will flash, indicating that the reset is successfuly initiated.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and confirm your sight's functionality. If you encounter any further difficulties, don't hesitate to seek help from Holosun's support.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• Beginning with, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, tap the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Permit the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option How to factory reset holosun eps carry red dot and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Restore your Holosun EPS Carry via a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the solution. This will set back your sight to its initial settings, clearing any altered configurations you've made. To execute this reset, observe these simple steps:

• To begin, locate the reset switch on your EPS Carry.
• Secondly, engage a fine object, like a toothpick, to depress the reset switch.
• As you hold the reset switch engaged, turn your EPS Carry.
• The sight will flash a message indicating that the reset is complete.

When the reset is finished, your EPS Carry will be back to its factory settings.

Report this wiki page